LTMP2 - Tutorial: Difference between revisions

From VASP Wiki
mNo edit summary
Line 21: Line 21:
</math>
</math>


Usually it is sufficient to set NOMEGA to 6. For materials with a not too large bandgap it is worth checking if the MP2 energy changes with increasing NOMEGA (e.g. 8 or 10). Note, that the MP2 energy diverges with 1/bandgap, independent of NOMEGA.
Usually it is sufficient to set NOMEGA to 6. For materials with a small bandgap it is worth checking if the MP2 energy changes with increasing NOMEGA (e.g. 8 or 10). Note, that the MP2 energy diverges with 1/bandgap, independent of NOMEGA.


== Parallelization ==
== Parallelization ==
Line 32: Line 32:
OpenMP threads per rank: 1 <br />
OpenMP threads per rank: 1 <br />
  KPAR = 256
  KPAR = 256
To decrease the memory requirement you can alternatively set <br />
To decrease the memory requirement you can alternatively set KPAR to 128 or 64 and so on. Or also try <br />
MPI ranks: 512 <br />
OpenMP threads per rank: 1 <br />
KPAR = 128
or <br />
MPI ranks: 512 <br />
OpenMP threads per rank: 1 <br />
KPAR = 64
and so on. Or also try <br />
MPI ranks: 256 <br />
MPI ranks: 256 <br />
OpenMP threads per rank: 2 <br />
OpenMP threads per rank: 2 <br />

Revision as of 09:23, 28 September 2018

On this page, we explain how to perform a calculation using the LTMP2[1] algorithm. Make sure you successfully completed the preparation steps Hartree-Fock ground state and Hartree-Fock virtuals.

The INCAR file

The LTMP2 calculation can simply be performed using the following INCAR file

ALGO = ACFDTRK 
LMP2LT = .TRUE.
NOMEGA = # number of tau points (see below)
NBANDS = # same valule as in the Hartree-Fock unoccupieds step ( = number of plane-waves)
ENCUT = # same value as in the Hartree-Fock step
LORBITALREAL = .TRUE.
PRECFOCK = Fast

Make sure that VASP reads the WAVECAR file from the Hartree-Fock virtuals step.

NOMEGA flag

The number of -points is controlled by the NOMEGA flag. This is necessary to calculate the Laplace transformed energy denominator (see Ref [1] for details),

Usually it is sufficient to set NOMEGA to 6. For materials with a small bandgap it is worth checking if the MP2 energy changes with increasing NOMEGA (e.g. 8 or 10). Note, that the MP2 energy diverges with 1/bandgap, independent of NOMEGA.

Parallelization

The LTMP2 algorithm is a high-performance code and can easily be used on many CPUs. Both OpenMP and MPI is supported. We recommend to use MPI for parallelization since the code possesses an almost ideal parallelization efficiency. OpenMP should only be used to increase the shared memory, if necessary.

In order to activate the efficient MPI parallelization use the KPAR flag in the following way (note that the usual meaning of the KPAR flag becomes obsolete in the LTMP2 algorithm). Set KPAR to half of the used MPI ranks. If this results in memory issues, further decrease KPAR (such that KPAR is alway a divisor of the used MPI ranks) or increase the number of OpenMP threads.

Example for 512 CPUs

MPI ranks: 512
OpenMP threads per rank: 1

KPAR = 256

To decrease the memory requirement you can alternatively set KPAR to 128 or 64 and so on. Or also try
MPI ranks: 256
OpenMP threads per rank: 2

KPAR = 128

References